- TSOP 17xx
- Transistor BC547
- Transistor BC557
- ATX Power Wiring
We use the +5 VSB wire and mass (COM)
And finally the assembly diagram that you'll need to make with care and patience ^ ^ well connect the masses, the +5 V supply, make no mistake make sense for transistor and capacitor, and for the diode. Small councils after the pattern!
Tips
- It is possible to use other resistances, it is after you make the tests, normally a resistor 22kohm could make the case for R3
- The scheme of the diode bar is the black line present on the diode, not mistaken sense, your circuit does not work ...
- The - the capacitor must be indicated on one side, same as for the diode, not the wrong direction!
- Good weld transistor, not the wrong pasta! Everything is shown on the diagram and the doc.
- Connect all bodies and all +5 V
- Do not be deceived by connecting son to feed your PC ...
- Do not be deceived of dough over the top of the relay is indicated by a small circle or half circle on it (I myself initially mistaken sense ...)
- Check your solder connections and, it costs nothing and saves a lot of trouble!
Once your installation is complete, you would get something like this:
When you are sure that your installation works, you can cut and plate your pasta in excess of your components.
It'll just plug in your module on your motherboard and your alim and press a button on your remote! If everything has been done your PC will turn on;)
Otherwise ... I advise you again to recheck your installation
Conclusion
We can say that this arrangement is still relatively simple and it really does not require extensive knowledge of electronics!
Moreover, it is inexpensive (I had to have for 15 € -20 € with the large plate test)
Moreover, once the PC turned on it will not be turned off with the remote control which avoids cuts intenpestive ... In any case I do, I pressed for more than 4sec and the computer remained on.
A remote control for DVD player
This is a new way to become even more lazy geek heu pardon
Benefits
- Low cost
- Easy to carry
- Efficient and works with virtually all IR remotes
- Good range (approximately 6m to 10m without obstacle probably)
Disadvantages
- Do not use another electronic device via IR remote in the same room if your PC could light up a time that you do not want ...
- Transistor BC547
- Transistor BC557
- ATX Power Wiring
We use the +5 VSB wire and mass (COM)
And finally the assembly diagram that you'll need to make with care and patience ^ ^ well connect the masses, the +5 V supply, make no mistake make sense for transistor and capacitor, and for the diode. Small councils after the pattern!
Tips
- It is possible to use other resistances, it is after you make the tests, normally a resistor 22kohm could make the case for R3
- The scheme of the diode bar is the black line present on the diode, not mistaken sense, your circuit does not work ...
- The - the capacitor must be indicated on one side, same as for the diode, not the wrong direction!
- Good weld transistor, not the wrong pasta! Everything is shown on the diagram and the doc.
- Connect all bodies and all +5 V
- Do not be deceived by connecting son to feed your PC ...
- Do not be deceived of dough over the top of the relay is indicated by a small circle or half circle on it (I myself initially mistaken sense ...)
- Check your solder connections and, it costs nothing and saves a lot of trouble!
Once your installation is complete, you would get something like this:
When you are sure that your installation works, you can cut and plate your pasta in excess of your components.
It'll just plug in your module on your motherboard and your alim and press a button on your remote! If everything has been done your PC will turn on;)
Otherwise ... I advise you again to recheck your installation
Conclusion
We can say that this arrangement is still relatively simple and it really does not require extensive knowledge of electronics!
Moreover, it is inexpensive (I had to have for 15 € -20 € with the large plate test)
Moreover, once the PC turned on it will not be turned off with the remote control which avoids cuts intenpestive ... In any case I do, I pressed for more than 4sec and the computer remained on.
A remote control for DVD player
This is a new way to become even more lazy geek heu pardon
Benefits
- Low cost
- Easy to carry
- Efficient and works with virtually all IR remotes
- Good range (approximately 6m to 10m without obstacle probably)
Disadvantages
- Do not use another electronic device via IR remote in the same room if your PC could light up a time that you do not want ...
Aucun commentaire:
Enregistrer un commentaire